Reference / Glossary
Motor Parts Machining Glossary
The words that show up on a motor part drawing, RFQ or quote, defined plainly and in one place.
Written by the team that reads your RFQLast reviewed How we write these
- Balance gradeA rotor unbalance limit from ISO 1940-1, written as a G number such as G6.3. Lower numbers are tighter. It is a property of the rotating assembly, not a single machined part. Read more →
- Bar stockSolid round or hex material a shop cuts a part from, as opposed to a casting or forging. No tooling cost, but more material is removed as chips.
- Bearing seatThe bore or journal a bearing is pressed into or onto. On a housing it is a bore with a clearance fit; on a shaft it is a journal with an interference fit. Read more →
- BlankThe raw piece a part is machined from, whatever form it starts in: bar, casting, forging or tube.
- BoreA machined internal cylindrical surface, most often the hole a bearing, shaft or spigot sits in.
- CastingA blank formed by pouring molten metal into a mould. Sand casting and permanent mould casting suit lower to mid volume; die casting suits high volume. Each leaves a different amount of stock for machining.
- ConcentricityA geometric tolerance controlling how closely a feature’s axis lines up with a datum axis. Two bearing bores on a motor housing are usually held concentric to each other.
- DatumA reference surface, axis or point a drawing measures other features from. A tolerance with no stated datum cannot actually be inspected against anything.
- Die castingHigh pressure casting into a reusable steel die, used at volume for aluminium alloys such as ADC12 and the A380/383 family. Fast cycle times, more as-cast porosity than gravity casting.
- EXW (Ex Works)An Incoterm meaning the buyer takes responsibility for the goods, and pays freight and insurance, from the shop’s door onward. The default quoting basis on this site.
- FAI (First Article Inspection)A report measuring every dimension on a drawing for one sample part before a full batch runs, used to confirm the process before committing to volume.
- FitThe relationship between a shaft and a bore of matching nominal size: clearance (shaft always smaller), interference (shaft always larger, an assembled press fit), or transition (can go either way depending on where each part lands in its tolerance).
- GD&TGeometric dimensioning and tolerancing. The symbol-based system, standardised as ISO 1101 internationally and ASME Y14.5 in North America, for controlling form, orientation, location and runout against stated datums.
- Hardness (HB, HRC)A material’s resistance to indentation, reported on the Brinell (HB) or Rockwell C (HRC) scale depending on range. Heat treat condition changes it far more than alloy choice does.
- Interference fitA fit where the shaft is always larger than the bore before assembly, so the parts are pressed or shrink fitted together and held by friction. The usual choice for a bearing inner ring on a rotating shaft.
- IT gradeAn ISO 286 tolerance grade, such as IT6 or IT7, defining a tolerance band width for a given size range. An H7 bore is a hole with zero lower deviation and an upper deviation equal to the IT7 value. Read more →
- JournalA precision-turned or ground section of a shaft that a bearing rides on.
- KeywayA machined slot in a shaft or bore that holds a key, transmitting torque between the shaft and whatever is mounted on it.
- Lamination stackThe stack of thin, insulated steel laminations that forms the rotor or stator core, built up to reduce eddy current losses.
- MachinabilityHow readily a material cuts: tool life, achievable surface finish and cycle time at a given cutting speed. Alloy, temper and heat treat condition all move it independently of hardness alone.
- PPAPProduction Part Approval Process, an automotive-derived documentation package proving a production process is capable and repeatable before parts ship at volume. More extensive than an FAI.
- Register (spigot register)A precision-machined step or shoulder used to locate one part against another, such as a motor end bell against the housing bore, independent of the fasteners.
- RoundnessA geometric tolerance controlling how close a circular feature is to a true circle. A bore can sit inside its size tolerance and still be oval enough to distort a bearing outer ring.
- RotorThe rotating assembly of a motor: shaft, lamination stack and, depending on motor type, magnets or windings.
- RunoutHow much a surface moves, measured with an indicator, as a part rotates about a stated datum axis. Different from roundness, and different from balance.
- SplineA set of parallel teeth machined on a shaft or in a bore, transmitting torque with more contact area and less backlash than a single keyway.
- StatorThe stationary assembly of a motor, typically a lamination stack with windings, held inside the housing.
- Surface finish (Ra)A roughness average, in micrometres or microinches, describing how smooth a machined surface is. Functional surfaces such as bearing journals and seal diameters need a stated Ra; most others do not.
- Tensile strength (UTS)The maximum stress a material withstands before it starts to fracture, usually reported as a range because heat treat, casting process and section size all move it.
- Turn-millA machine combining turning and milling, often with a sub-spindle, that can complete a part in one setup instead of moving it between a lathe and a machining centre. Keeps concentric features concentric by construction.
- Water jacketA cast or machined cavity around a motor housing that liquid coolant circulates through, used where air cooling cannot remove enough heat.
- Yield strengthThe stress at which a material begins to deform permanently rather than springing back. Lower than tensile strength, and the number a structural calculation usually designs against.
Missing a term?
If a word on your drawing or a shop's quote is not here, ask at and it goes on the list.